Steering Wheel Covers

Steering wheel covers

Learn the proper steps to install a leather steering wheel wrap to protect your vehicle’s steering wheel.

Leather steering wheel covers not only help protect the steering wheel from daily wear and tear or sun damage, but also greatly enhance the driving experience by providing excellent grip for better handling.

Here you will get the knowledge to perform a baseball stitch installation on any newly purchased or homemade leather steering wheel cover for girls.

Steering Wheel Covers

Steering Wheel Covers
Steering Wheel Covers

The regular instructions that usually come with a store bought leather wrap show a typical loop stitch. If what you are looking for is the original factory look then you will need to know how to use a baseball stitch.

1) To get started, take the leather steering wheel wrap and stretch it all over the steering wheel. Make sure the temperature in your vehicle is not too hot or cold, as leather stretches easily in hot weather and becomes less stretchable in cold weather. Place the cover over the bottom of the steering wheel and stretch it along the sides.

Don’t forget to use your fingers to stretch it over the top of the wheel. At this point, you should be a little careful not to pull too hard on the seam, as you can easily tear it. Double check it to see if it is carefully aligned so that the seam is where it is supposed to be. It is usually over the location of the previous seam, but you may want it to be a bit more to the front or back.

Consistency is important here, as a seam that snakes inside the rim can make installation difficult. A quick tip is to turn slowly as you sew so you can pull evenly from both the front and the back.

Cool Steering Wheel Covers for Your Car

2) Now you can start with the sewing of the leather steering wheel wrap. You will need 2 needles for this. Start by passing one end through each seam seam in the middle, located at the bottom of the ruffle. Tie the 2 threads together and then 1 thread comes out at each seam. Pass about 7 inches of yarn and tie 2 or 3 knots to tie the ends together. After that, you can pass the threads so that the knot is in the seam.

3) Carefully cut off the excess thread to about a quarter inch, but make sure it’s not too close. Make sure to use holes that are directly opposite each other. To start the stitches, be sure to cross the threads above and below the seam, as well as on the opposite side. One important thing to keep in mind is that you will need to cross the threads in the same way consistently each time.

Custom steering wheel covers

4) Do not start sewing at the seam as this will make it very difficult to pull hard. Similar to a loop stitch, you need to pull each stitch hard before moving on to the next. When you try to tighten each stitch individually, you will notice that the wax on the thread helps to hold the previous stitches tight. Get one for you custom steering wheel covers visit here.

The correct way to pull is steady and slow rather than quick, jerky movements. Also, pull straight to the sides and not forward as you could accidentally overstretch the cover if pulled incorrectly.

5) Slowly and methodically should be your method when trying to install a steering wheel cover for the first time. Handling the string is the most challenging step, but doing it slowly and safely will help you achieve an easier pace. Prepare about 2-3 hours to successfully perform the baseball stitch on the leather steering wheel cover.

You will notice that when it comes down to a radius, the baseball stitch has clear advantages over a loop stitch method. First, you will have a thread on each side of the radius that will allow you to wrap the thread on both sides. Second, you will be able to pull the seam tighter and closer to the spokes than with a loop stitch.

What are the best steering wheel covers?

6) You have now reached your first radio on the wheel. To cross the spokes of the wheel, use a loop stitch by winding the thread around and into the next hole on both sides of the spoke of the wheel. Pull each and every stitch as hard as possible with a steady, firm pull.

Don’t worry about breaking the waxed thread as it was designed to withstand a lot of abuse. After you get to the other side of the wheel spoke, pick up the next pair of holes that you can close almost completely and continue.

Best Steering Wheel Covers Reviews (Recommended Picks)

  • AXX Wheelskins Universal Size Steering Wheel Cover.
  • BDK SW-352-DW steering wheel cover.
  • Aumo-mate car steering wheel cover.
  • SEG Direct Auto Car Car Steering Wheel Cover.
  • Plasticolor Star Wars steering wheel cover.
  • QUEES Cowhide leather car steering wheel cover.

7) If the leather wheel cover is the correct size, it will not stretch too much if you continue sewing. There will be some clumping, but this is normal in the installation process.

Do the steering wheel covers ruin the steering wheel?

If you are looking for a small change to your vehicle, a steering wheel cover is an affordable option that is easy to install yourself. In addition, the cover prevents damage to the steering wheel itself. Since the steering wheel is used every time the vehicle is driven, it can show wear and tear over time.

After reaching the bottom again, take the last few stitches and pull them over and over under the original knot while pulling the threads through the seam. Then you will need to tie several knots and then cut off the excess seam. Make sure to leave at least a half inch of slack and tuck the knot into the seam.

8) Take a flat head screwdriver and press the knots and thread ends directly into the seam. Do this carefully and carefully, as you may accidentally cut the thread if the screwdriver is too sharp. The main reason you should leave a little extra thread at the end after knotting is so that the knots can loosen a bit if necessary. Leaving a bit of thread will prevent them from separating entirely.

Install Steering Wheel Cover

Now you have successfully learned all the steps on how to install a steering wheel cover. Don’t worry if your first attempt at installing a leather steering wheel wrap didn’t turn out as perfect as you planned, as you can always start over by going back to where you have a good seam.

The most important factor here is keeping the seam straight while continuing to sew. If you come across a knot, don’t try to pull it up, rather use the needle to untie the knot.

Leather steering wheel covers are a great investment and will enhance the look of your steering wheel as well as provide better grip and handling.

  • Top 10 Steering Wheel Covers | Leather is Most Popular.